Insights

Glass Beads or Aluminium Oxide for Stainless Steel and Aluminium Parts?

Nov 07, 2026 Editorial 3 min read
Glass Beads or Aluminium Oxide for Stainless Steel and Aluminium Parts?

Use glass beads when a stainless steel or aluminium part needs cleaning and a satin finish without any change to its dimensions. Use aluminium oxide when the surface needs a sharp anchor profile for paint, powder coat or bonding, or when rust, scale and old coating must be cut away. Glass beads peen the surface; aluminium oxide cuts it.

How do glass beads and aluminium oxide differ?

PropertyGlass beadsAluminium oxide
MaterialSoda-lime glassFused aluminium oxide (Al2O3), brown or white
ShapeSphericalAngular grain
Hardness5.5 to 6 Mohs9 Mohs
ActionPeening, with little material removedCutting, leaving an anchor profile
FinishSatin to matteUniform matte texture
Sizes we supply70 to 850 microns, in fine, medium and coarse gradesGrit 16 to 220 (brown 16 to 220, white 46 to 220)
ReuseMultiple blasting cycles4 to 6 cycles for brown 60 to 80 grit in a well-kept cabinet
Packing25 kg bags or custom packing25 kg PP woven bags, 50 kg jumbo bags or loose bulk

The round bead peens instead of cutting, so it cleans and polishes while keeping tolerances. The angular grain cuts on contact, so it removes more and leaves a rougher surface. On carbon steel our aluminium oxide gives a surface profile from about Ra 1.5 µm with fine grits to Ra 6.5 µm with coarse grits.

Which media suits stainless steel parts?

For a cosmetic finish, glass beads. They leave a bright satin surface and no ferrous contamination, which helps the part keep its corrosion resistance. Fabricators use them for weld cleaning and for finishing stainless steel, and medical equipment makers use them for clean, uniform matte stainless surfaces.

Choose aluminium oxide when stainless steel has to be prepared for a coating, or when a finer grit is wanted for a dull polish look: at 220 grit it leaves a surface close to a dull polish. If iron contamination matters, ask for the white grade. It is over 99% Al2O3, and our page lists it for work where trace metal from the brown grade is not acceptable.

Which media suits aluminium parts?

Glass beads are the gentler choice. In the automotive trade they are used for aluminium wheel restoration, engine component cleaning and mould cleaning, where the part must come out clean while the base material stays intact.

Aluminium oxide is the choice before a finish goes on. Grit 80 to 120 gives a smooth, bright, lower-profile surface that suits anodising preparation on aluminium. Coarser grits, 16 to 46, are used in blast cabinets for aggressive preparation on steel, aluminium and titanium parts.

Which should you pick for the job in hand?

JobMedia
Satin finish, dimensions must not changeGlass beads, fine grade
Cleaning welds on stainless steelGlass beads
Cleaning moulds and diesGlass beads
Anodising preparation on aluminiumAluminium oxide, grit 80 to 120
Powder coat preparation on mild steelAluminium oxide, grit 60 to 80 (about Ra 2 to 4 µm)
Heavy scale, thick paint, weld spatterAluminium oxide, grit 16 to 24

For coating preparation on stainless steel or aluminium, our pages do not print a grit figure, so send us the coating system and we will suggest one.

What blasting machine do they need?

Both are reusable, so both work best in an enclosed system that recovers the media. Our cabinet sand blasting machine blasts parts inside a sealed chamber and captures and recycles the abrasive, which keeps consumption down. Aluminium oxide also runs in pressure blasters at 40 to 100 PSI with grits 24 to 80, and in suction blast guns with grits 60 to 120. For glass beads, tell us your machine and pressure and we will suggest the bead grade.

Where can you order glass beads and aluminium oxide?

We supply glass beads for sandblasting in graded sizes and aluminium oxide in brown and white grades, from New Delhi to customers across India. Tell us the part material, the finish you want and your blasting equipment, and we will recommend the media and grade. The full range, including steel shot and steel grit, is on our abrasives page.

Need engineering advice on this topic? Our team responds within 24 hours with a tailored solution.
WhatsApp